Switchboard audits, digitisation and monitoring upgrades

For switchboards already in service. We audit the board as it stands, record it as current drawings and a 3D model, and fit monitoring equipment so the board reports its own condition.

Rendered 3D model of a main switchboard built from the CWS design model
A rendered 3D model of a main switchboard. Example model, not a client site.

Full board safety audit

A structured review of an existing switchboard, on site. We check the board against six areas: a defined and supported design, protection matched to the circuits, correct fault duty, an enclosure and layout that can be used safely, clear identification and current records, and monitoring that serves a purpose.

You receive a written report: what was found, what matters most and the options for each item. It is a condition review to plan work from. It is not a certificate of compliance.

The six checks explained

Existing air circuit breaker cubicle with the breaker removed, photographed during a switchboard survey
An existing breaker cubicle opened for survey, with the breaker withdrawn.

How the work is staged

1. Audit the board

Start with the board as it stands. Send photographs, the nameplate, any drawings and the fault level if it is known. The audit sets the priorities for everything after it.

2. Digitise it

We survey the board and redraw it: single line diagram, schematics, layout and a 3D model of the assembly. A board with no drawings, or drawings that no longer match, gets a current record.

3. Fit monitoring equipment

Sensors and a gateway are fitted during a planned shutdown. Wireless sensors need no signal wiring to each point, which suits boards that were never built for monitoring.

Monitoring equipment we fit
Equipment is selected for the board and the site. What can be fitted depends on the board’s construction and safe access.
What is measuredEquipmentWhere it goes
Temperature of connectionsSchneider PowerLogic TH110 wireless thermal sensorsBusbar joints, cable terminations and circuit breaker connections.
Temperature and humidity in the cubicleSchneider PowerLogic CL110 wireless sensorsOn a de-energised surface inside the enclosure.
Early signs of overheating insulationSchneider PowerLogic HeatTagIn the cubicle air. It is an early warning device, not a fire protection device.
Power and energyPower meters and circuit breaker meteringIncomers and selected feeders.
Collecting the readingsSchneider EcoStruxure Panel Server gatewayIn the board, connected to your network.

4. Decide where the data goes

Readings and alarms go to the gateway, then to your SCADA, BMS or the manufacturer’s software. Who owns the network connection, the software and any subscription is agreed in the scope.

5. Upgrade what the audit finds

Where the audit finds obsolete breakers or a section at the end of its life, the same survey informs the next step: an ACB retrofit, a replacement section or a new board. Compare upgrade and replacement.

Board digitisation and 3D models

CWS builds full 3D models of switchboards and switchrooms. The model shows the board as built: sections, doors, devices and cable zones, to scale. Use it to plan modifications, brief contractors before a shutdown and check access without opening the board.

The model and drawings are a record of one particular board. Linking that record to live readings from the monitoring equipment is scoped project by project.

Rendered 3D model of a switchroom with the roof removed, showing switchboards, drives and air conditioning
A rendered 3D model of a switchroom. Example model, not a client site.

Monitoring on boards we build

CWS has fitted EcoStruxure Panel Server gateways in distribution boards and motor control centres. On a new board, monitoring points are agreed at design stage so sensor positions, clearances and access are allowed for in the layout.

Protection and monitoring options for new switchboards

Audit, digitisation and monitoring questions

What does a board safety audit cover?

Six areas: the design and its supporting records, protection, fault duty, the enclosure and layout, identification and drawings, and monitoring. You receive a written report with the findings in priority order.

What is a switchboard digital twin?

A digital record of one particular board: its single line diagram, schematics and a 3D model of the assembly as built. With monitoring fitted, readings from the board can be read against that record.

Can sensors be fitted to an older switchboard?

Often. Wireless sensors need no signal wiring to each point, but they do need safe access to the connections, so fitting is planned for a shutdown. The board is assessed first.

Does fixed temperature monitoring replace a thermal imaging survey?

No single method does everything. Fixed sensors watch chosen connections continuously. A thermal survey looks across the board at one moment. Both belong in the maintenance plan.

Where does the monitoring data go?

To a gateway in the board, then to your SCADA, BMS or the manufacturer’s software. The network connection, software and any subscription are agreed in the scope.

Do you audit switchboards built by other manufacturers?

Yes. We work on main switchboards, motor control centres and distribution boards built by others. Send the drawings and nameplate details you have.

Start with a board audit

Send the site location, board photographs, nameplate details and any drawings. Tell us what you want to know about the board.

IP Geolocation by DB-IP · CC BY 4.0