Outdoor switchboard kiosks for exposed sites

We build switchboards into free-standing outdoor kiosks for pump stations, container yards, sports grounds and solar sites. The enclosure, finish, heating and cable entry are settled for the site before the board is laid out.

Stainless steel outdoor kiosk with doors open, showing a 400 A distribution board behind white front plates

400 A reefer kiosks in 304 stainless steel

Two 400 A kiosks for a refrigerated container yard. Each has a load break switch incomer, a distribution section and switched socket outlets for the containers, in a custom 304 stainless steel enclosure.

Reefer kiosk ratings
Ratings of this project. They do not transfer to another kiosk.
ItemAs built
Rated current400 A
Short-time withstand20 kA for 1 second
Form of separationForm 2b
Enclosure protectionIP55
EnclosureCustom 304 stainless steel, 1,400 × 1,630 × 400 mm
Cable entryBottom

Read the full project: 400 A reefer power kiosks.

Inside a stainless steel outdoor kiosk: 400 A main switch and circuit breaker rows wired in red cable
The 400 A incomer and outgoing circuits inside one of the stainless steel kiosks.

Plan your outdoor kiosk

Site and exposure

Tell us where the kiosk stands: coastal or inland, sun, wind-driven rain, washdown, public access and vehicle traffic. An IP rating alone does not make an enclosure suitable for every outdoor site. How to choose a switchboard IP rating.

Enclosure and finish

Custom 304 or 316 stainless steel, or a Rittal CS outdoor enclosure. A kiosk can be left as stainless steel or powder coated to a specified colour. CWS has its own powder coating plant in Invercargill.

Kiosks we have built
Ratings belong to each project and do not transfer to another kiosk.
Enclosure and finishWhat it housesStated ratings
Custom 304 stainless steel, unpainted400 A distribution and socket outlets for refrigerated containers, Form 2bIP55, 20 kA for 1 second
Custom 316 stainless steel, powder coatedKiosk enclosure for a water booster pump stationIP55
Rittal CS outdoor enclosure, powder coated160 A distribution board for a solar site, Form 1IP55, 20 kA for 1 second
Rittal CS outdoor enclosure in marine grade aluminium, powder coated250 A bore pump kiosk, Form 1IP55, 20 kA for 1 second
Rittal CS outdoor enclosure, light grey160 A outdoor main switchboard with contactors, timer and meteringNot stated here

Heat and condensation

An outdoor kiosk takes sun on the doors by day and cold at night. We allow for anti-condensation heaters and thermostats, and for the heat given off by the equipment inside.

Cable entry, plinth and roof

Confirm bottom or top entry, gland plates, plinth height and whether a canopy or rain hood is needed. Send the slab or plinth drawing if one exists.

Access and locking

Tell us who opens the kiosk and how it should lock. Front plates behind the doors keep live parts covered when the kiosk is open.

Powder coated stainless steel for a pump station

A custom 316 stainless steel kiosk for a water booster pump station, powder coated and built with an overhanging roof. Enclosure protection IP55.

Powder coated stainless steel outdoor kiosk for a pump station, double doors closed
Powder coated 316 stainless steel kiosk, doors closed, ready to leave the workshop.

An outdoor main switchboard for a sports ground

A 160 A main switchboard in a Rittal CS outdoor enclosure, with contactors, a timer and metering behind front plates, and a cabinet heater against condensation.

For charging sites, see EV charging switchboards and kiosks.

Light grey outdoor kiosk with doors open, showing a main switchboard with white front plates and a cabinet heater
Front plates fitted, with the cabinet heater at lower left.

Outdoor kiosk questions

What is a switchboard kiosk?

A free-standing outdoor enclosure that houses a switchboard, so the board can stand on its own plinth without a building or switchroom.

Stainless steel or aluminium?

Both are used. Grade 304 and 316 stainless steel suit custom sizes. Rittal CS outdoor enclosures come in standard sizes. The choice depends on corrosion exposure, size and finish. Tell us the site conditions.

What IP rating do your kiosks have?

The kiosks listed on this page were built to IP55. The rating belongs to the completed assembly, so it is confirmed for each design, including its cable entries.

Do you build EV charging kiosks?
What do you need to quote a kiosk?

A single line diagram or circuit schedule, the supply and fault level, the site location and exposure, the cable entry and any size limits.

Request a kiosk quote

Send the circuit schedule, supply details, site location and any limits on size or finish.

IP Geolocation by DB-IP · CC BY 4.0